Wheels

Front RockShox/SRAM-specific Torque-Cap 15mm through-axle SealLock end caps for Neo and Neo Ultimate hubs. SealLock end caps feature a low-friction U-cup seal that snaps into place and stays secure even when your wheel is removed from your bike. Torque-Cap end caps have the same 15mm inside diameter as other systems, but outside diameter is larger (31mm), making these end caps only compatible with Torque-Cap-compatible forks. Note: Torque caps are not compatible with centerlock hubs.

Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs - SealLock end caps feature a low friction U-cup seal that snaps into place

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Compatible with straight valve hole Hugo 52 rims and designed to fit 7.5 - 8.5mm valve holes. Sold as a pair. Identifying your Hugo rim and selecting the correct valve stem: Stepped Hugo rims have a larger diameter valve hole on the interior of the rim, and a narrower hole on outside of the rim. Quick tip: don't remove your tire if you don't have to. If your Hugo rim decal reads: MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this valve. For "Stepped" valve hole Hugo use part AS0105 - Valve Stem pair, Schrader, 32mm, 14mm base.

In the early design phases of our Traverse Fattie 29, we recognized that the number of aluminum wheels that had the prowess to both shred rowdy descents and to provide the efficiency required of our Northern California testing grounds' relentless climbs were far and few between. We also came to realize that trail riders expect certain features in a proper, send-it-ready wheelset. And for the price, we found that alloy hit many of these expectations, while also keeping enough jingle-jangle in your wallet for a post-ride beverage. Along with light overall weight, stiffness, and durability, another top priority for the Traverse was ease of use. First off, we got rid of the creaky straight-pull spokes and corrosion-prone alloy nipples. Next up, we landed on 28 J-bend spokes, for front and rear wheels, that are all the same length—making it easy to find replacements if needed. And finally, we engineered a new hub design, with a wider profile and higher flange to aid in overall stiffness. We took the traditional 19- to 23-millimeter standard and moved it out to what we found worked best in testing—a whopping 30mm “Fattie” width. A wide rim does a variety of things for ride performance—it better supports the tire for increased confidence and grip, it affords you the ability to run lower pressures, and it spreads impact out over a larger surface area to reduce the risk of damage. We also added our Zero Bead hook design to the mix, and this ultimately aids in preventing “burps” during hard cornering, while also making tubeless set up quick and easy. After developing what we found to be the perfect alloy trail wheels, we went farther down the perfection path, hand-lacing the rims to our own alloy hubs that allow for the same spoke length throughout the entire wheelset, via 28 DT Swiss Revolution J-Bend spokes and Pro Lock nipples. Inside our hubs, you'll find sealed cartridge bearings and DT Swiss 360 rear internals that'll keep you rolling smoothly for miles. We also wanted to ensure that each wheel was built correctly, so we built them by hand. Each wheelset comes packaged with a SRAM XD-driver and a tubeless valve stem in order to make tubeless set-up a touch easier. Please note that Shimano freehubs are sold separately.

XD is a cassette driver body that allows the use of a 10-tooth small cog and provides an improved interface with the cassette on your SRAM Rise 60 wheels. • Driver body design that lets riders tap the power and range of the SRAM 10-42 11-speed Cassette and a 10-tooth small cog • Provides a stable hub connection

Elevating Weekend Hot Laps to World Cup XC Status From weekend hot laps to World Cup XC finals, the Control Carbon combines the low weight and strength found in our world-beating Control SL rim with the new DT Swiss 350 hubs. An unmatched level of durability, precision, and performance in this new Carbon Control wheelset that is purpose-built to open terrain, from gut-wrenching climbs to tear-inducing descents – a whole new era of riding. A high-performance wheel that excels everywhere from world cup xc races to your favorite weekend trail. The Control Carbon combines the low weight and strength found in our world-beating Control SL rim with the new DT Swiss 350 hubs and spokes. This level of quality, precision and performance has previously been found only on wheels costing twice as much. - Rim: Control SL 29, 29mm Internal Width, Zero Bead Hook 4mm FlatTop Design, Tubeless Compatible, Compatible with Tire Inserts - Spoke Pattern: 28-Hole Two-cross (1:1) Non Driveside Front and 28-Hole Two-cross (1:1) Rear - Spoke Type: DT Competition Race Straighpull—Front Driveside 301mm, Non-Driveside 300mm , Rear Driveside 298mm, Non-Driveside 301mm - Nipple Type: DT Swiss Hexagonal Prolock Alloy - Hub: DT Swiss 350 Straight-pull, 6-bolt, 36t Star Ratchet System, 110x15mm & 148x12mm thru-axle compatible - Weight: Set—1450g w/ Tubeless Rim Tape - Assembly Method: Hand-built - Extras: 19 and 31mm OD end cap options included, Roval Spoke Kit, Tubeless Rim Tape and Valves, Lifetime warranty - System Weight Limit: 275lbs/125kg

Taking the notion of combining flagship performance with workhorse dependability one step further, we're introducing the Terra C. This shares the same hub and spoke architecture as the Terra CL, ensuring ease of service and spoke replacement, should the need arise and is paired with an entirely new rim layup. The rims on the Terra C share the same dimensions and broad range of tire mounting possibilities as the Terra CLX and CL—33mm deep with a 25mm internal width—but are crafted using a new-to-us process known as Resin Transfer Molding. This is an automated process that allows us to very precisely control how resin is introduced to the layup, which in turn ensures maximum strength and material performance. The end result is an incredibly tough set of wheels that you can beat on to hell and back. - Rim: Terra C RTM Carbon Clincher, 700c, Disc Brake, Tubeless Compatible - Rim Details: 32mm Depth, 30mm External Width, 25mm Internal Width; ERD 577mm - Hub: DT Swiss 370 J-bend Center Lock, Ratchet LN 18t internals (20 degs), 100x12mm & 142x12mm, Shim. Rd. 11sp Freehub (Convertible freehub ) - Bearing Type: DT Swiss Sealed Steel Cartridge Bearings - Spokes: DT Swiss Competition Race J-bend, Front: Radial/Two-cross 24 count, R: 268mm, L: 279mm; Rear: Two-cross 24 count, DS: 277mm NDS: 278mm - Nipple: DT Swiss Hex Prolock Al 2.0x14mm - Tire Size: 28mm - 47mm; Max Pressure: 28c-32c: 80psi, 33c – 36c: 65psi, 37c- 47c: 60psi - Weight: Wheelset 1,610g, Front 719g, Rear 891g (including tubeless rim tape and tubeless valve) - Assembly Method: Carbon Layup - Automated, Wheel Build - Hand built. - Extras: Roval Tubeless Rim Tape and Tubeless Valve, Spare Spoke & Nipple Kit - System Weight Limit: 275lbs / 125kg

Following directly in the tire tracks of the Terra CLX, the new Terra CL utilizes the same super-light, incredibly tough rim as our flagship wheel. It's a hook-bead, 33mm deep carbon fiber rim with a 25mm inner width that plays well with tubeless setup and allows you to mount tires anywhere from 28mm to 47mm wide at whatever pressure you feel like running. In a nod to accessibility, durability and real-world serviceability, we opted to use ultra-dependable DT Swiss 350 hubs and lace them to the rims with DT Swiss Competition Straightpull spokes. The net effect of these changes is a wheelset that is almost as light as our incredibly light Terra CLX, offering close to the same benchmark performance but with more easily sourced spokes in the event of some back-of-beyond carnage, all with a price tag that is about half that of our flagship product. - Rim: Terra CLX Carbon Clincher, 700c, Disc Brake, Tubeless Compatible - Rim Details: 32mm Depth, 30mm External Width, 25mm Internal Width; ERD 577mm - Hub: DT Swiss 350 Straight-pull Center Lock, Star Ratchet 36t internals (10 degs), 100x12mm & 142x12mm, Shim. Rd. 11sp Freehub (Convertible freehub ) - Bearing Type: DT Swiss Sealed Steel Cartridge Bearings - Spokes: DT Swiss Competition Race Straightpull, Front: Two-cross (1:1) 24 count, R: 287mm, L: 286mm; Rear: Two-cross (1:1) 24 count, DS: 284mm NDS: 287mm - Nipple: DT Swiss Hex Prolock Al 2.0x14mm - Tire Size: 28mm - 47mm; Max Pressure: 28c-32c: 80psi, 33c – 36c: 65psi, 37c- 47c: 60psi - Weight: Wheelset 1,408g, Front 654g, Rear 754g (including tubeless rim tape and tubeless valve) - Assembly Method: Hand built at every step; from rim layup to the last nipple turn. - Extras: Roval Tubeless Rim Tape and Tubeless Valve, Spare Spoke & Nipple Kit - System Weight Limit: 275lbs / 125kg

Replacement freehub bodies for Vault hubs. - Use to replace worn/damaged freehub body or to switch cassette standards. - 60T

The Muc-Off Tubeless Rim tape is made from their proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy.

Confident and capable of cleaning the A-line yet budget-friendly to save up for a season of bucket-list rides, the 1/1 hub stays true to the performance heritage of Industry Nine. - High-load sealed cartridge bearings - Classic j-bend spokes - Robust protection system using a labyrinth radial lip seal and endcap proximity seals unencumbered by bearing wear or preload - CNC machined, anodized, and assembled entirely in Asheville, NC - Unified service parts across the range

These lightweight valves help prevent clogging from tubeless sealant. - Aluminum - 40mm length

Industry Nine Hydra Classic hubs are the heart of your wheelset, everything revolves around them, literally. Every Classic Hydra hub is made from start to finish in Asheville, NC. From turning and milling bar stock 7075-T6 aluminum for shells, axles, and endcaps, wire EDM cutting A2 tool steel for pawls and driverings, to in-house anodization lab, every step of design, engineering, manufacturing, and assembly is done to exacting standards. - 690 P.O.E. Hydra Freehub body engages every 0.52 degrees, yielding telepathic control - 6 pawl, 6 phase - 115 tooth drivering - Easily serviced with no proprietary tools—designed to keep you in the saddle and out of the service queue

Industry Nine Classic hubs are the heart of your wheelset, everything revolves around them, literally. Every Classic mountain hub is made from start to finish in our Asheville, NC machine shop. From turning and milling bar stock 7075-T6 aluminum for shells, axles, and endcaps, wire EDM cutting A2 tool steel for pawls and driverings, to our own in-house anodization lab, every step of design, engineering, manufacturing, and assembly is done on-premises to our exacting standards. Hydra Classic mountain hubs are loaded with features every rider will appreciate, such as revolutionary 0.52° engagement, generously low weights, and an intuitive layout that can be serviced without any proprietary tools.

Proven ENVE gravel wheel technology comes to the Foundation family with the AG25. Ready for high-speed adventure. - Intended Use: Gravel, Bikepacking - Inner rim width: 25mm - Recommended Tire Size: 36mm – 50mm - Tubeless Optimized; Tube Compatible Preparation is key to a successful adventure into uncharted territories. Our experiences developing and riding the flagship G Series and M Series have created a quiver of performance enhancing features that have been incorporated into the AG25. Features like our patented Wide Hookless Bead, tuned carbon materials, external nipples and our Foundation Road Hub all come together for a gravel wheel that's more than the sum of its parts. It's ready to take an already exceptional bike to a level of even higher performance and higher fun. Wide Hookless Bead Flat Protection Goodbye to pinch flats: The cringe-inducing impact between rock and rim is something we've all experienced when the desire to shred trail overwhelms our better judgement. Unless you're running too much tire pressure, that impact will typically result in a pinch flatted tire. Gravel Ride Tune By using on board data acquisition equipment and aligning it with subjective test ride feedback, our laminate design team have refined the AG25 to deliver a ride quality that is both responsive and compliant, supportive yet forgiving. - Shallow rim depth of 21mm allows improves vertical compliance and vibration damping - Rim cross-section and laminate optimized for responsive power transmission and cornering stability Built to Shrug Off Your Bad Ideas So, you've decided to descend that mountain bike trail on your gravel rig. Or maybe you didn't have a choice, it was the only way to get from point A to point B. No worries, we encourage it. Which is why we've designed and tested the Foundation AG wheels using our proven M Series impact testing protocol. The result is a wheel that inspires confidence when you need it the most, even when you aren't looking for it. External Molded Nipples Reliability first, serviceability also first: By employing ENVE's patented molded spoke hole technology and configuring it for external nipples, you can rest assured that you're riding a wheel that's been built for reliability and serviceability when you need it most. Enve Foundation Road Hub Utilizing ENVE's core hub technologies the Foundation Road Hub delivers a high performance, maintenance-free ride experience. - Flange spacing and hub shell geometry designed to maximize performance metrics such as wheel and drive stiffness - ID360 40t drive mechanism delivers efficient and responsive power transmission - Maintenance free premium full contact sealed NTN steel bearings - Perfect Preload USA Made, Protected for Life It's no secret that we at ENVE are proud of our U.S. based manufacturing capabilities. Like all our rims, the Foundation Collection and its AG25 are handmade and assembled in our Ogden, Utah based, state-of-the-art carbon wheel manufacturing facility. The AG25 is covered under ENVE's Lifetime Incident Protection program and 5 Year Factory Warranty.

ENVE AM30 Carbon Wheelsets use a 30mm inside width rim that is tuned for compliance and damping for performance on All-Mountain, Enduro, and Trail riders. - 30mm internal rim width - Gravity rated impact strength - Rim shape tuned for compliance and damping - Wide Hookless Bead Anti-pinch flat technology

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set. - DT 350 20x110mm Left Dust Cap

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.

The entry into the world of gravel riding, the G 1800. If you want to give cycling a try and plan to do your first rides off-road the G 1800 is your choice of wheel. Combining all the key advantages of DT's gravel segment wheels at a very attractive price point, these wheels may be your entry into the world of gravel riding. Leave for beaten roads and turn to the unexplored paths, the G 1800 will join you. - 370 based hub

Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs.

Torque Axle End Cap - 110 x 15mm Black

Zipp's 101 XPLR is a purpose-built wheel for gravel. Thanks to MOTO Technology, this wheel arms gravel cyclists with more control and durability over harsh terrain, providing a smooth ride quality that helps reduce fatigue. That means a more comfortable ride. The 101 XPLR—short for explore-is purpose—built for riders searching for adventure beyond the norm. Think of it as a magic carpet ride over primitive roads, especially with large tubeless tires at lower tire pressures. This wheel is ideal for gravel racing, adventure, or any long day in the saddle. Based on Zipp's MOTO Technology, the 101 XPRL's single-wall rim construction provides excellent compliance and vibration damping. Less fatigue, allows you to ride longer and faster. The 101 XPLR features the ZR1 hubset for better seal design for improved durability and quicker response with 66 points of engagement. With 101 XPLR, victory is in the pursuit of adventure. - All-day comfort and compliant ride - Available in 700c or 650b - 27mm wide internal profile - Reduced chance of pinch flatting - More traction in rough corners - Smoother ride in rocky terrain - Ability to run lower tire pressure - Less fatigue, which allows you to ride longer and faster - Frustration-free tire installation - ZR1 hubset for better seal design for improved durability and quicker response with 66 points of engagement - Lifetime Warranty

Zipp's 101 XPLR is a purpose-built wheel for gravel. Thanks to MOTO Technology, this wheel arms gravel cyclists with more control and durability over harsh terrain, providing a smooth ride quality that helps reduce fatigue. That means a more comfortable ride. The 101 XPLR—short for explore—is purpose-built for riders searching for adventure beyond the norm. Think of it as a magic carpet ride over primitive roads, especially with large tubeless tires at lower tire pressures. This wheel is ideal for gravel racing, adventure, or any long day in the saddle. Based on Zipp's MOTO Technology, the 101 XPRL's single-wall rim construction provides excellent compliance and vibration damping. Less fatigue, allows you to ride longer and faster. The 101 XPLR features the ZR1 hubset for better seal design for improved durability and quicker response with 66 points of engagement. With 101 XPLR, victory is in the pursuit of adventure. - All-day comfort and compliant ride - Available in 700c or 650b - 27mm wide internal profile - Reduced chance of pinch flatting - More traction in rough corners - Smoother ride in rocky terrain - Ability to run lower tire pressure - Less fatigue, which allows you to ride longer and faster - Frustration-free tire installation - ZR1 hubset for better seal design for improved durability and quicker response with 66 points of engagement - Lifetime Warranty

Zipp's 101 XPLR is our first purpose-built rim for gravel. Thanks to MOTO Technology, this wheelset arms gravel cyclists with more control and durability over harsh terrain, providing a smooth ride quality that helps reduce fatigue. That means a more comfortable ride. The 101 XPLR -short for explore-is purpose-built for riders searching for adventure beyond the norm. Think of it as a magic carpet ride over primitive roads, especially with large tubeless tires at lower tire pressures. This rim is ideal for gravel racing, adventure, or any long day in the saddle. Based on Zipp's MOTO Technology, the 101 XPRL's single-wall rim construction provides excellent compliance and vibration damping. Less fatigue, allows you to ride longer and faster. Quarq's TireWiz is an add-on option for 101 XPRL to dial in your pressure for an even more compliant ride. - All day comfort and compliant ride - Available in 700c or 650b - 27mm wide internal profile - Reduced chance of pinch flatting - More traction in rough corners - Smoother ride in rocky terrain - Ability to run lower tire pressure - Less fatigue, which allows you to ride longer and faster - Frustration-free tire installation - Lifetime Warranty

Zipp's 101 XPLR is our first purpose-built rim for gravel. Thanks to MOTO Technology, this wheelset arms gravel cyclists with more control and durability over harsh terrain, providing a smooth ride quality that helps reduce fatigue. That means a more comfortable ride. The 101 XPLR -short for explore-is purpose-built for riders searching for adventure beyond the norm. Think of it as a magic carpet ride over primitive roads, especially with large tubeless tires at lower tire pressures. This rim is ideal for gravel racing, adventure, or any long day in the saddle. Based on Zipp's MOTO Technology, the 101 XPRL's single-wall rim construction provides excellent compliance and vibration damping. Less fatigue, allows you to ride longer and faster. Quarq's TireWiz is an add-on option for 101 XPRL to dial in your pressure for an even more compliant ride. - All day comfort and compliant ride - Available in 700c or 650b - 27mm wide internal profile - Reduced chance of pinch flatting - More traction in rough corners - Smoother ride in rocky terrain - Ability to run lower tire pressure - Less fatigue, which allows you to ride longer and faster - Frustration-free tire installation - Lifetime Warranty

Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).

Road bikes are going where they’ve never gone before, are expected to do more, and are being ridden harder than ever. At the same time disc brakes are rewriting the rules of what’s possible with rim design. For this new era, the Zipp 303 Firecrest Tubeless Disc-brake wheelset sets the new standard. With a disc-specific, tubeless rim, the 303 Firecrest Carbon Clincher is now internally 21mm wide and faster than ever. Designed from the start as a tubeless rim, the 303 Firecrest features a rim bed made with internal ridges to lock the tire’s bead in place, ensuring secure performance, even when ridden at lower tire pressures. A new carbon fiber layup keeps weight low while maintaining the 303’s legendary durability. The rim’s lightweight design allows the 303 to glide up the steepest climbs while SRAM's robust 77/177D hubset keep the wheels stiff and responsive. Each Wheel Includes: - Zipp Tubeless valve extender and valve-core wrench - Zipp rim tape (factory taped) - Zipp Tangente quick-release skewer - Zipp thru-axle end caps

Zipp's 303 Firecrest Tubeless wheels are designed for the real world—a world of imperfect conditions, varying road surfaces, and elements where the bottom line is simple: efficiency = speed. They're faster, lighter, and more capable over varied terrain—whether the surface is pavement in all its conditions or no pavement at all. Deeply rooted in Zipp's drive to conquer the Spring Classics, the new 303 Firecrest is remade with a purpose-made approach for the demands of modern road bikes. When it comes to going fast on a bicycle, efficiency means reduced wind resistance, rolling resistance, rider fatigue, and weight. The 303 Firecrest Tubeless Disc-brake was designed using real-world direct measurements (vs. primarily wind tunnel or computer simulation). The results were huge. Its rim is slightly more bulbous in design than its predecessor, with a 32mm outside width, a 25mm internal width, and a 40mm rim depth. The profile provides low drag and an improved transition between rim and tire, boosting aero efficiency on the road. The wide rim stance also features less tire deflection for reduced rolling resistance. The combination of the wider tire, increased tire volume, and lower tire pressure helps to reduce rider fatigue by smoothing out the ride over imperfect pavement and road conditions—the tire and wheel system absorbs the shaking, not the rider. At the center of the 303 Firecrest Tubeless is a versatile and durable new hubset, the German-engineered ZR1 DB. This hubset features 66 points of engagement for quicker response. The 303 Firecrest Tubeless wheels are for dedicated cyclists who aspire to the latest in technology. They're for those who compete in races, against peers, or simply to conquer personal limits. - New Zipp graphics and cosmetic identity that scream speed - Versatile endurance wheelset for the modern road bike with tubeless and hookless rim profile - Lighter weight than its predecessor, making it nimble and fast - Tubeless Made Easy, optimized tire bed sign allows for simple tool-free installation and removal with no need for an air compressor to seat the tire. - Ultra-wide 25mm rim profile creates a better tire interface to be fast on or off the road - 40mm rim depth makes a light and aero wheel in every situation - Ships with 12mm end caps - Center Lock rotor interface (lockring included)